1188164 Imer Combi 250VA Wet Rail Saw
Imer Combi 250VA Tile Stone Saw
The Imer Combi 250VA electric tile cutter is lightweight and able to plunge cut. The extruded aluminum travel bar design provides a smooth accurate cut. Maintenance is minimal, just spray n'wipe with DW-40 and you're good to go.
- Free shipping from IMER factory warehouse
- 1.75 hp motor, 110V, blade speed 2800 Rpm this saw has hi-torque at low Rpm to deliver fast, chip free, cutting performance
- Maximum cutting depth 2-1/2", 1-1/4" with 90/45 degrees cuts
- 45 degree miter cuts, just tilt the cutting head
- Adjustable cutting head makes plunge cuts and L cuts a snap
- The stand and side table are very light yet stable and strong
- Cast aluminum make for a rigid and light weight saw at 72 lbs and the all new cast aluminum protractor is truly and accurate rip guide
- Imer Combi 250 VA Wet Tile Saw
- Tile Saw Stand
- Side Table Extension
- 10 in Diamond Blade (installed)
- Water Pump in Pan
- Rip Guide
- Protractor Guide
- Spare Parts
- Operator's manual
|Imer CombiCut 250VA Tile Saw Specifications|
|Power||Direct Drive - 1-3/4 hp (15 amps)|
|Length of Cut||28 in (31 in w/ plunge)|
|Diagonal Cut||22 in|
|Blade Capacity||10 in|
|Depth of Cut||2-1/2 in|
|Dimensions||40 in x 22 in x 18 in|
"Today's tile and stone pieces are larger and more expensive than in years past. Consequently, architects and their clients want the pieces set very close together for that striking "slab look." This requires accurate, chip free cutting performance. The Combi 250VA delivers this performance for the most demanding installations, day after day. GUARANTEED!" - Mace T. Coleman Jr
Questions & Answers (8)
I have one of these, and the spring that makes the motor goes up and down it broke, how can I find it? I already looked at the imer web site and I couldn't, can u guys help me please?
Imer sells all the parts direct for the Imer Combi 250VA Tile Saw. Please call Imer (800) 365-4003 .
Your specs for all the imer 250 saws show a max cutting depth of 3 3/4 inches. My local supplier has one on display and with the blade even with the table it has less than 3 inches of clearance under the motor. Can you verify if the 3 3/4 in is correct?
With a 10" diamond blade the Imer Combi 250 Tile Saw has a 3-3/4" depth of cut. The saw at your local supplier was a Imer Combi 200 which has a 8" blade with a 2-3/4" depth of cut.
How much is a water tub for imer combi 250 2003 model
Dino ceramic tile
Imer sells all combi 250 tile saw parts direct. Please call Imer (800) 275-5463.
I am looking for a replacement pump and assembly for a comb 200-va model # 3210524
Imer USA takes care of all their parts orders. Please call them at 1-800-275-5463 to place an order for your part.
Cuanto cuesta el motor para CM 250 VA, cod. 1188164?
Imer USA vende sus partes directo al cliente . Por favor, póngase en contacto con ellos al 1-800-275-5463.
Hello I have this saw and it keeps shutting off on me then if I wait about 15 20 minutes it will start to work again. Any ideas what this could be?
Thanks for contacting Contractors Direct. When did you purchase this saw?
Please contact us or Imer USA (301) 336-3700 for warranty information.
Need off on switch for older imer 250 saw
For parts please contact Imer directly 800-275-5463 and they can advise the correct part number for the switch that is needed for your saw.
Laser guide is included?
No laser guide is included with this saw
Ratings & Reviews
by tileman -
the only drawback for this saw is the miter gauge. It doesn't stay in place when making a cut.
Great Saw for larger tiles
by JDS TILE -
It would be nice if the extention tray fit the right side of the saw also. Like any other tool its how you and your men use and take care of them that will determine how straight they will cut and how long they will last. Great Saw
by Workin Man -
I own the previous version of this saw which has the frame made out of steel and no side table. All I can say is it is truly a wonderful saw to use. I don't think I've ever cracked a tile while cutting it even free hand off the table for say around a closet ring in a bathroom. If you do get it definitely get a wet tent with it so you can use it inside when it gets cold outside. Super great combo! It also got to me quick from these guys
by Tile Joe -
I love this saw. It is light, powerful, and the rip capacity is enough to do 99% of the jobs I encounter. I will never go back to a fixed head saw again, the sliding head provides a much needed feature of scoring the surface of the tile before cutting through, this keeps porcelain from breaking where you don't want it. If there is a Con to the saw, it is the table. It is easy to fix by applying a peice of corian to the top. Overall, this saw is excellent and I will buy another when I need to.
by Doug -
Bought this saw to do a job with 22" porcelan tile set diagonly so I needed the big cut capacity. I also fitted it with the porcellana blade. After using this I am getting rid of my old saw. It would drive me nuts to use it after the smooth cuts the Imer Combi 250VA makes. I also used it to cut 1" stone to line the shower niche. Only drawback I found was that some water would run on the floor between the main table and the extension table when cutting the big tiles. I built a 40"x44"x2" deep sheet metal pan to set the whole arangement in, tossed in a few rags, and this woorked great. I love the plunge feature. It made cutting heat register slots and the small stones in the deco band a breeze.
by Populin -
Purchased this saw two years ago from Contractors Direct and it still runs like new. I've owned 20 different wet saws over the years and If I were to weigh pros and cons this has the best features by far. Power, lightweight, ease of set up, and accurate. Free shipping to top it off.
by Scabman -
So far so good. Going to have to retire my MK saw. This one does it all and then some. Need a wet tent though.